Converter Lithium Charger

0 Orders
#32799779376
39931 in stock
$10.50 $6.03
Clear selection

Description

1.When you use the product, the module inputs and outputs to be isolated from ground.

2.USB output voltage is consistent with the module, not a fixed 5V output. When charging for digital equipment, make sure USB output voltage is 5V.

3.Some customers report:“The module can not adjust the output voltage is always equal to the input voltage.”When you encounter this problem, please counterclockwise rotation of the“voltage potentiometer”10 laps or more, then use the module you can adjust the output voltage. Because the factory default output voltage of about 20V.

Specifications

1.Input voltage range:5-36VDC

2.Output voltage range:1.25-32VDC adjustable

3.Output current: 0-5A

4.Output power: 75W

5.High efficiency up to 96%

6.Built in thermal shutdown function

7.Built in current limit function

8.Built in output short protection function

9.Input reverse polarity protection: None (if required, high current diode in series with the input).

10.L x W x H =68.2×38.8×15mm

11.Weight: 39g

Application

1.Use as a step-down modules with overcurrent protection

Usage:

(1) Adjust the right button so that“OUT”LED lighted, Digital meter shows the value of output voltage ,adjust the“voltage potentiometer”so that the output voltage reaches the value you want.

(2) Adjust the right button so that Digital meter shows the value of output current;Wire shorted output terminal, then adjust the“current potentiometer”so that the output current reaches a predetermined overcurrent protection value. (For example, the Digital meter displays the current value of 4A, then you can use the module to a maximum current of 4A)

(3) Connected to the load.

2.Use as a battery charger

Usage:

(1) Make sure you need to charge the battery float voltage and charging current; (if lithium parameters 3.7V/2200mAh, then the float voltage is 4.2V, the maximum charging current 1C, ie 2200mA)

(2)Under no-load conditions, adjust the“Voltage potentiometer”so that the output voltage reaches the float voltage; (if to 3.7V rechargeable lithium battery, the output voltage can be adjusted to 4.2V)

(3)Adjust the right button so that Digital meter shows the value of output current;Wire shorted output terminal, then adjust the“current potentiometer”so that the output current reaches a predetermined Charging current value.

(4)Charge turn lamp current factory default is 0.1 times the charging current; (Battery during charging current is gradually reduced, if the charge current setting is 1A, then when the charge current is less than 0.1A, blue lights turned off, the green light is on, which means that the battery is fullycharged)

(5)connected to the battery charge.

(1,2,3,4 steps as: Output is unloaded, do not connect the battery)

3.Use as a LED constant current driver module

Usage:

(1)Adjust the“voltage potentiometer”so that the output voltage reaches the value you want.

(2)Adjust the right button so that Digital meter shows the value of output current;Wire shorted output terminal, then adjust the“current potentiometer”so that the output current reaches a predetermined LED operating current.

(3)Connect LED, work.

(1,2 steps as: Output is unloaded, do not connect LED)

Voltmeter and ammeter calibration method:

Module with manual calibration function can correct display precision voltage and current, if you think the current voltage and current accuracy to meet the requirements, do not perform the following operations.

(1) Output voltage calibration steps

Step 1, adjust the right button so that“OUT”LED lighted, Digital meter shows the value of output voltage; Press the right button for more than 2 seconds, release, Digital meter and“OUT”LED flashes in synchronization so that you enter the output voltage calibration mode.

Step 2, press the right button (normal speed), the voltage value is adding up a unit; Press the left button, minus a unit; Due to a unit is less than 0.1V, the minimum voltage display to 0.1V, so you need to continuously press 1-5 times to see the voltmeter change 0.1V, how many times voltmeter change 0.1V by pressing the key, depending on the current display voltage, the higher the voltage, the fewer the number of press.

Step 3, press the right button for more than 2 seconds, release, to exit the output voltage calibration mode. All parameters set to automatically power down to save.

(2) Input voltage calibration steps

Step 1, adjust the right button so that“IN”LED lighted, Digital meter shows the value of input voltage; press the right button for more than 2 seconds, release, Digital meter and“IN”LED flashes in synchronization so that you enter the input voltage calibration mode.

Steps 2 and 3, consistent with the output voltage calibration method.

(3)Output current calibration steps

Step 1, adjust the right button so that Digital meter shows the value of output Current. Press the right button for more than 2 seconds, release, Digital meter flashes in synchronization so that you enter the output current calibration mode.

Step 2,Connected to the load, ammeter in series, adjust the right and left button to change the display of digital meter, so that is consistent with the ammeter display .

Module name: 12A synchronous rectifier decompression module, constant voltage constant current
Module property: non – isolating pressure module (BUCK) synchronous rectifier
Input voltage: 4-32V (limit 35V) please keep the voltage margin.

Adjustable output voltage: 1.2-32V (default output around 18V, if to the module is powered on, found around rotating potentiometer voltage output voltage is always did not change, you first the voltage potentiometer counterclockwise circle above 15)
Input output minimum differential pressure: 0.8V
Output current: 0-12A time natural heat dissipation 8A, temperature not exceeding 60 degrees.
Use when the temperature is high.
Output constant current range: 0-12A
Working temperature: -40~+85 degrees
Working frequency: 150KHz
Conversion efficiency: highest 98% (efficiency is related to input, output voltage, current, differential pressure)
Short circuit protection: (limited current is current constant current value)
Input reverse protection: no (if you need to enter a diode in the input string)
Output anti-retro-protection: no (if you need to put the diode in the output string, please add the anti-diodes between the output of the module and the battery when used for charging application, otherwise it will damage the module.)

The method of setting voltage and current:
1, set the output voltage: according to you want to charge the battery of float charging voltage value, or after leds in series, in parallel, adjust the voltage value of constant pressure potentiometer (CV), the output voltage is set to the required voltage.
(without load)
2. Set constant current value: turn the first CC potentiometer into 20 circle-clockwise, and short-circuit output with multimeter 20A current, and adjust the CC potentiometer to the current value that you need to set.
Note: the voltage of constant current setting is higher than 1.2 V, otherwise the constant current function will fail.

Additional information

Brand Name

WAVGAT

Condition

New

Type

electronic module

Model Number

XL4015

Application

experimental modules

Operating Temperature

-40-+85

Supply Voltage

4-38V

Dissipation Power

5A / 12A

Package

module

is_customized

Yes

Reviews

There are no reviews yet.

Be the first to review “Converter Lithium Charger”

Your email address will not be published. Required fields are marked *

Tags

UPSELL PRODUCTS